152 lines
4.4 KiB
ReStructuredText
152 lines
4.4 KiB
ReStructuredText
================================
|
|
EL7 Quickstart (CentOS and RHEL)
|
|
================================
|
|
|
|
Install Warewulf and dependencies
|
|
=================================
|
|
|
|
.. code-block:: bash
|
|
|
|
sudo yum install -y golang tftp-server dhcp nfs-utils
|
|
|
|
git clone https://github.com/hpcng/warewulf.git
|
|
cd warewulf
|
|
make all
|
|
sudo make install
|
|
|
|
Configure firewalld
|
|
===================
|
|
|
|
Restart firewalld to register the added service file, add the service
|
|
to the default zone, and reload.
|
|
|
|
.. code-block:: bash
|
|
|
|
sudo systemctl restart firewalld
|
|
sudo firewall-cmd --permanent --add-service warewulf
|
|
sudo firewall-cmd --permanent --add-service nfs
|
|
sudo firewall-cmd --permanent --add-service tftp
|
|
sudo firewall-cmd --reload
|
|
|
|
Configure the controller
|
|
========================
|
|
|
|
Edit the file ``/etc/warewulf/warewulf.conf`` and ensure that you've
|
|
set the appropriate configuration parameters. Here are some of the
|
|
defaults for reference assuming that ``192.168.200.1`` is the IP
|
|
address of your cluster's private network interface:
|
|
|
|
.. code-block:: yaml
|
|
|
|
ipaddr: 192.168.200.1
|
|
netmask: 255.255.255.0
|
|
warewulf:
|
|
port: 9873
|
|
secure: false
|
|
update interval: 60
|
|
dhcp:
|
|
enabled: true
|
|
range start: 192.168.200.10
|
|
range end: 192.168.200.99
|
|
template: default
|
|
systemd name: dhcpd
|
|
tftp:
|
|
enabled: true
|
|
tftproot: /var/lib/tftpboot
|
|
systemd name: tftp
|
|
nfs:
|
|
systemd name: nfs-server
|
|
exports:
|
|
- /home
|
|
- /var/warewulf
|
|
|
|
.. note::
|
|
|
|
The DHCP range ends at ``192.168.200.99`` and as you will see
|
|
below, the first node static IP address (post boot) is configured
|
|
to ``192.168.200.100``.
|
|
|
|
Start and enable the Warewulf service
|
|
=====================================
|
|
|
|
.. code-block:: bash
|
|
|
|
# Start and enable the warewulfd service
|
|
sudo systemctl enable --now warewulfd
|
|
|
|
Configure system services automatically
|
|
=======================================
|
|
|
|
There are a number of services and configurations that Warewulf relies
|
|
on to operate. If you wish to configure all services, you can do so
|
|
individually (omitting the ``--all``) will print a help and usage
|
|
instructions.
|
|
|
|
.. code-block:: bash
|
|
|
|
sudo wwctl configure --all
|
|
|
|
.. note::
|
|
|
|
If you just installed the system fresh and have SELinux enforcing,
|
|
you may need to reboot the system at this stage to properly set the
|
|
contexts of the TFTP contents. After rebooting, you might also need
|
|
to run ``restorecon -Rv /var/lib/tftpboot/`` if there are
|
|
errors with TFTP still.
|
|
|
|
Pull and build the VNFS container and kernel
|
|
============================================
|
|
|
|
This will pull a basic VNFS container from Docker Hub and import the
|
|
default running kernel from the controller node and set both in the
|
|
"default" node profile.
|
|
|
|
.. code-block:: bash
|
|
|
|
sudo wwctl container import docker://warewulf/centos-7 centos-7 --setdefault
|
|
sudo wwctl kernel import $(uname -r) --setdefault
|
|
|
|
Set up the default node profile
|
|
===============================
|
|
|
|
The ``--setdefault`` arguments above will automatically set those
|
|
entries in the default profile, but if you wanted to set them by hand
|
|
to something different, you can do the following:
|
|
|
|
.. code-block:: bash
|
|
|
|
sudo wwctl profile set -y default -K $(uname -r) -C centos-7
|
|
|
|
Next we set some default networking configurations for the first
|
|
ethernet device. On modern Linux distributions, the name of the device
|
|
is not critical, as it will be setup according to the HW
|
|
address. Because all nodes will share the netmask and gateway
|
|
configuration, we can set them in the default profile as follows:
|
|
|
|
.. code-block:: bash
|
|
|
|
sudo wwctl profile set -y default --netname default --netmask 255.255.255.0 --gateway 192.168.200.1
|
|
sudo wwctl profile list
|
|
|
|
Add a node
|
|
==========
|
|
|
|
Adding nodes can be done while setting configurations in one
|
|
command. Here we are setting the IP address of ``eth0`` and setting
|
|
this node to be discoverable, which will then automatically have the
|
|
HW address added to the configuration as the node boots.
|
|
|
|
Node names must be unique. If you have node groups and/or multiple
|
|
clusters, designate them using dot notation.
|
|
|
|
Note that the full node configuration comes from both cascading
|
|
profiles and node configurations which always supersede profile
|
|
configurations.
|
|
|
|
.. code-block:: bash
|
|
|
|
sudo wwctl node add n0000.cluster --netname default -I 192.168.200.100 --discoverable
|
|
sudo wwctl node list -a n0000
|
|
|
|
Turn on your compute node and watch it boot!
|